Heating Controls Explained: How to Set Your Thermostat, Programmer and TRVs

Heating Controls Explained: How to Set Your Thermostat, Programmer and TRVs

Most homes with a gas, oil or LPG boiler have three main heating controls: a programmer (or timer), a room thermostat and thermostatic radiator valves, usually called TRVs, on the radiators. Each does a different job. Set them up so they work together and your home stays comfortable without the boiler running more than it needs to.

This guide explains what each control does and how to set it sensibly. If your heating won’t come on at all, start with our heating won’t come on checks instead.

What each control does

  • Programmer or timer: decides when the heating (and, if you have a hot water cylinder, the hot water) comes on and goes off.
  • Room thermostat: decides how warm the house gets. It keeps the heating running until the room it’s in reaches your chosen temperature, then switches it off until the room cools a little.
  • TRVs: fine-tune each room by controlling how much hot water flows through that radiator. As the room warms up, the valve lets less water through.
  • Cylinder thermostat (only if you have a hot water tank): stops the stored water getting hotter than it needs to be.

The Energy Saving Trust says a boiler system should have at least a programmer, a room thermostat and TRVs, plus a cylinder thermostat if there’s a hot water tank. A programmable room thermostat combines the timer and thermostat in one unit, and smart controls do the same jobs through an app.

Which programmer do you have?

According to the Energy Saving Trust, programmers usually come in three types:

  • Single channel: common with combi boilers. It only times the heating, because a combi heats hot water on demand.
  • Two channel: usually a system or regular boiler with a hot water cylinder, so heating and hot water have separate times. Some combi homes use two channels for upstairs and downstairs zones.
  • Three channel: hot water plus two separate heating zones.

Your user manual will show exactly how your model works. If you’ve lost it, most manufacturers have manuals on their websites. Search for the make and model printed on the front of the control.

How to set your heating controls: step by step

  1. Set the clock first. Check the time and day on the programmer are right, especially after a power cut or when the clocks change.
  2. Programme the heating around your day. Set it to come on a little before you get up and before you get home, and to go off when you go out or go to bed. In very cold weather, bring the start time forward rather than turning the thermostat up.
  3. Set the room thermostat to the lowest comfortable temperature. The Energy Saving Trust says that’s between 18°C and 21°C for most people. Turning it up higher won’t warm the house any faster; it just keeps the heating on for longer.
  4. Leave the thermostat alone when it’s cold outside. The house will still warm to the set temperature. It may simply take a little longer.
  5. Set each TRV for its room. Start in the middle of the dial (often 3). If the room feels too warm, turn it down a number; too cool, turn it up. Lower numbers mean a cooler room. The numbers aren’t the same temperature on every make.
  6. Keep the room with the thermostat fully open. If the radiator in the same room as your room thermostat has a TRV turned down low, the thermostat may never reach its target and the heating can run on. Leave that radiator’s valve open, or ask us about the best layout.
  7. Don’t switch rooms off completely in winter. Keep a little background heat in spare rooms. It helps prevent condensation and mould, and it protects pipes from freezing.
  8. Let the controls “see” the room. Don’t cover the room thermostat or TRV heads with curtains, furniture or radiator covers, and keep the thermostat away from direct sun, lamps and draughty doors.
  9. Check the hot water times if you have a cylinder. The Energy Saving Trust recommends the cylinder thermostat is set to 60°C, hot enough to kill harmful bacteria but also hot enough to scald. If you’re not sure what yours is set to, ask your engineer to check it at the next service rather than opening the cylinder’s covers yourself.
  10. Write your settings down. A note next to the controls helps everyone in the house, and anyone looking after it while you’re away.

Older people and anyone vulnerable to the cold

Comfort and health come before saving money. The Energy Saving Trust notes that you may need a higher minimum temperature if someone at home is older, has a health condition that makes them more vulnerable to the cold, or spends long periods indoors. If you go away in winter, leave the heating on low rather than off; our frost precautions guide explains why.

What you shouldn’t do

Heating controls are designed to be set by you, from the outside. Some jobs need a professional:

  • Don’t open control covers or touch the wiring. Moving, replacing or rewiring a thermostat, programmer or wiring centre is electrical work and should be done by a competent, registered electrician or heating engineer (Part P of the Building Regulations applies to home electrical work).
  • Don’t remove the boiler casing, adjust gas valves or burners, or touch the flue. Under the Gas Safety (Installation and Use) Regulations 1998, only a Gas Safe registered engineer may work on gas appliances and pipework. You can check an engineer on the Gas Safe Register.
  • Stick to the user manual for the boiler itself. Your part is limited to user-manual actions: checking the power, the timer and thermostat, pressing the reset button and topping up the pressure through the filling loop as the manual describes. If it keeps locking out or losing pressure, call a Gas Safe engineer. See our low boiler pressure and boiler fault code guides.
  • Don’t force a stuck TRV. A valve pin that’s stuck after summer is a common reason one radiator stays cold. Our some radiators cold guide covers what to check; if it won’t free up, leave it for a plumber.

If the consumer unit trips when the heating comes on, you can reset the RCD or breaker once, with dry hands. If it trips again, leave it off and call a registered electrician. Never touch electrics near water.

If you smell gas or suspect carbon monoxide

  1. Leave the property. Open doors and windows on the way out if it’s safe to do so.
  2. Don’t use light switches, electrical switches or anything with a naked flame.
  3. Turn the gas off at the meter only if it’s safe to do so.
  4. Call the National Gas Emergency Service on 0800 111 999.
  5. If anyone has headaches, dizziness, sickness or breathlessness, get medical advice straight away.

More in our guides to what to do if you smell gas and the signs of carbon monoxide.

If a leak appears while you’re checking radiators

Turn off the inside stopcock first; it’s usually under the kitchen sink. The outside stop tap at the boundary normally belongs to the water company (Anglian Water or Essex & Suffolk Water), may need a special key and shouldn’t be dug up or forced. Report any leak on their side to them, and ask your neighbours if they’re affected too. Our stopcock guide and radiator leaking guide explain more.

When to stop and call us

  • The heating won’t respond to the programmer or thermostat even with the time and settings right and fresh batteries in any wireless thermostat.
  • The heating runs constantly, or won’t switch off when the thermostat is satisfied.
  • One or more radiators stay cold whatever the TRV is set to.
  • You’d like controls moved, upgraded or replaced, for example a programmable or smart thermostat, or TRVs fitted to radiators that don’t have them.
  • The boiler keeps locking out or losing pressure.
  • Anything trips the electrics more than once.

We handle boiler repairs, boiler servicing, central heating installation and upgrades and domestic electrical work for homes across our local area.

Heating not behaving? Call us

Call 01787 278511 or WhatsApp 07825 348536. With over 10 local engineers, we’ll attend as soon as possible, even at midnight.

Anglian PHE Ltd, Top Floor, 4 Market Hill, Clare, Sudbury CO10 8NN. Gas Safe 572792, NAPIT registered, trading since 1993, and no call-out fee.

Sources

This is general safety guidance. If you’re unsure, stop and call a qualified engineer.

Similar Posts