Moving Into a New Home: Your Plumbing, Heating and Electrics Checklist
Moving Into a New Home: Your Plumbing, Heating and Electrics Checklist
Moving day is busy enough without a surprise leak or a boiler you can’t work out. Spending half an hour on a few simple checks in your first week means you’ll know where everything is before you actually need it, and you’ll have a short list of anything worth getting looked at properly.
This checklist covers the water, heating and electrics in a typical house or flat. None of it involves taking anything apart. If something looks wrong, make a note and leave the repair to the right qualified person.
Day one: the three things to find first
- The inside stopcock. This turns off the water to the whole house. It’s most often under the kitchen sink, but it can be in a downstairs toilet, a utility room, a garage or under the stairs. Turn it gently clockwise to check it moves, then open it fully again. If it’s stiff or seized, don’t force it. Our stopcock guide explains more.
- The gas meter and its control lever (if you have mains gas). It’s usually in an outside meter box or a cupboard near the front door. Just note where it is. You only touch it in an emergency.
- The consumer unit (fuse box). Find it and check you can reach it in the dark. A torch nearby is a good idea.
Tell everyone in the household where all three are. In a leak or a power cut, knowing this saves minutes.
Water: a quick first-week routine
- Run the kitchen cold tap. If the house has been empty for a while, Anglian Water suggests running the kitchen tap for up to five minutes before drinking the water or cooking with it, because water that has sat in the pipes can taste a little musty. Collect it in a bucket for the garden rather than wasting it. If an odd taste or smell keeps coming back, see our guide to tap water that tastes or smells odd.
- Find and read the water meter (if you’re metered). Meters can be inside, for example under the kitchen sink, in an airing cupboard or behind a toilet, or outside in a small chamber in the footpath near your boundary. Take a photo of the reading on the day you move in and give it to your water company so your bill starts from the right number.
- Do a simple leak test. With every tap off and nothing using water (no washing machine, dishwasher or toilet filling), note the meter reading, wait an hour or so and read it again. If it has moved, you may have a leak. Our water meter leak test walks you through it.
- Look under sinks and around the toilet, bath and washing machine. Check for damp cupboard bases, water marks, drips from fittings or a toilet that keeps running.
- Check the hot water. Run each hot tap and the shower briefly and note if any take a very long time to warm up or run with very low pressure.
Inside stopcock vs outside stop tap
Always use the inside stopcock first. The outside or boundary stop tap, usually under a small cover in the path or pavement, normally belongs to the water company (Anglian Water or Essex & Suffolk Water, depending on where you live). It may need a special key. Don’t dig it up or force it. If you think there’s a leak on their side of the boundary, contact your water company, and check whether your neighbours are affected too. Read more about the outside stop tap and boundary box.
In an older property, it’s also worth checking the pipe coming up from the ground near the stopcock. A dull grey, soft-looking pipe may be lead. See our guide to lead pipes in an older home.
Heating and hot water
- Find the boiler’s make and model on the front or underside, then download the user manual from the manufacturer’s website if the previous owner didn’t leave one.
- Ask for the paperwork. Ask the seller, landlord or agent for the boiler’s last service record, any warranty details and, for gas appliances, any Gas Safety records. If there’s no record of a recent service, book one with a Gas Safe registered engineer before winter.
- Check the pressure gauge (most combi and system boilers have one). The manual will give the normal range, often around 1 to 1.5 bar when the heating is cold. If it’s low, you can repressurise using the filling loop exactly as the manual describes. Our low boiler pressure guide explains how.
- Set the controls to suit you. The previous owner’s timer settings probably won’t fit your routine. Our guide to heating controls explains the programmer, room thermostat and radiator valves.
- Run the heating for an hour and feel each radiator (carefully, as they get hot). Note any that stay cold, are cold at the top, or are leaking at the valves.
Gas safety: under the Gas Safety (Installation and Use) Regulations 1998, only a Gas Safe registered engineer may work on gas pipework or gas appliances. Don’t remove the boiler casing, adjust anything inside it or touch the flue. Your part is limited to what the user manual allows, such as the reset button, repressurising, and checking the timer, thermostat and power. If the boiler keeps locking out or losing pressure, call a Gas Safe engineer. You can check an engineer is registered at www.gassaferegister.co.uk.
Electrics and alarms
- Look at the consumer unit. Check for a “Test” or “T” button, which tells you there’s an RCD. Electrical Safety First says pressing it should switch off power to the circuits it protects. Switch it back on straight afterwards. If there’s no RCD, or you see scorch marks, damage or discolouration, get it checked.
- Check sockets, switches and light fittings for burn marks, cracks, crackling sounds or a warm or burning smell. Electrical Safety First also flags sockets mounted in skirting boards as a sign the wiring may be older.
- Test the smoke alarms. There should be at least one smoke alarm on every floor, plus a heat alarm in the kitchen. Press each test button. See our smoke and heat alarm guide.
- Check for a carbon monoxide alarm in any room with a gas, oil or solid-fuel appliance. If there isn’t one, fit one following the manufacturer’s instructions. Know the signs of carbon monoxide.
- Ask for the latest EICR (Electrical Installation Condition Report). Electrical Safety First points out that a standard home survey doesn’t cover electrical safety. There may be a label in the consumer unit showing when it was last inspected. If there’s no recent report, ask a registered electrician to carry one out. Our EICR guide explains what it involves.
If a breaker or RCD trips while you’re settling in, you can reset it once. If it trips again, leave it off and call a registered electrician. Never touch electrics near water. Any electrical work beyond that, including new sockets or changes to the consumer unit, should be done by a registered electrician (Part P of the Building Regulations). Our RCD tripped guide has more.
Keep a simple home file
Put these in one folder, or take photos and keep them in one album on your phone:
- Photos showing where the stopcock, gas meter and consumer unit are
- Your move-in water meter reading and the meter serial number
- The boiler make, model, manual and last service record
- The latest EICR and any electrical certificates
- Your water company’s and energy supplier’s contact numbers, plus the National Gas Emergency Service number below
If you smell gas or suspect carbon monoxide
- Get everyone out of the property.
- Open doors and windows on the way out if it’s safe to do so.
- Don’t use light switches, electrical switches or anything with a naked flame.
- Turn the gas off at the meter only if it’s safe to do so.
- Call the National Gas Emergency Service on 0800 111 999.
- If anyone has headaches, dizziness, sickness or breathlessness, get medical advice straight away.
More in our guide to what to do if you smell gas.
When to stop and call us
- The stopcock is seized, leaking or impossible to find.
- Your meter test suggests a leak inside the property, or you find damp or drips under sinks or around fittings.
- The boiler has no recent service record, keeps locking out or keeps losing pressure.
- Radiators stay cold, leak, or the hot water takes ages to arrive.
- There’s no recent EICR, the consumer unit has no RCD, or you spot scorch marks, crackling or a burning smell.
- A breaker or RCD trips more than once.
We can help with plumbing, leak detection, boiler servicing, boiler repairs and domestic electrical work, including EICRs, for homes across our local area. If something goes wrong urgently, see our emergency plumbing page.
Just moved in? Call us for a check
Call 01787 278511 or WhatsApp 07825 348536. With over 10 local engineers, we’ll attend as soon as possible, even at midnight.
Anglian PHE Ltd, Top Floor, 4 Market Hill, Clare, Sudbury CO10 8NN. Gas Safe 572792, NAPIT registered, trading since 1993, and no call-out fee.
Sources
- Electrical Safety First: advice for home buyers
- Anglian Water: welcome to your new home (PDF)
- Gas Safe Register: what to do in a gas emergency
- Your boiler’s user manual (available on the manufacturer’s website)
This is general safety guidance. If you’re unsure, stop and call a qualified engineer.