Boiler Pressure Keeps Dropping? Safe Checks and When to Call

Topped up your boiler pressure, only to find the gauge creeping back down a few days or weeks later? A heating system that keeps losing pressure is telling you that water is escaping somewhere, or that a part needs attention. The good news is there are a few simple, safe checks you can do to narrow it down before an engineer visits, which can save time on the day. Please don’t take the cover off the boiler or touch any gas, pressure relief or expansion vessel parts. Finding the cause inside the boiler is a job for a Gas Safe registered engineer.

How much pressure loss is normal?

Some loss over time is expected. Worcester Bosch says a heating system will usually need topping up once or twice a year, and that you should get in touch if you’re having to repressurise much more often. Ideal Heating adds that a gradual drop over several months doesn’t necessarily mean the boiler itself is faulty, because the pressure is shared by the whole central heating circuit. A fault is more likely when the pressure drops repeatedly over days or weeks, falls to zero, or needs frequent topping up.

Common reasons the pressure keeps falling

  • A small leak somewhere in the heating system, for example at a radiator valve, a towel rail, a pipe joint, or pipework under the floor.
  • Radiators have recently been bled. Letting air and water out lowers the pressure, so a single drop afterwards is expected.
  • Water escaping through the pressure relief valve. This often follows overfilling, and you may notice drips from the small copper pipe that usually runs from the boiler to an outside wall.
  • A part inside the boiler, such as the expansion vessel, needing an engineer’s attention.

Safe checks you can do yourself

  1. Start a simple pressure log. With the heating off and the system cool, note the reading on the gauge each morning, along with the date. Write down whenever you top up. This record is really useful for an engineer.
  2. Look at every radiator and towel rail. Check the valves at each end and the bleed valve at the top for drips, damp patches, green or white crusty deposits, or rust marks. Kitchen roll wiped around a valve will show up even tiny weeps.
  3. Check under the boiler and along visible pipework. Look for drips, damp or staining on the pipes beneath the boiler, but don’t open the casing or any panel.
  4. Look for hidden-leak clues. Damp patches or stains on ceilings, walls or floors, lifting floor coverings or a musty smell can all point to a leaking heating pipe.
  5. Check the pipe on the outside wall. From a safe, dry spot, see whether the small copper pipe from the boiler is dripping or has a damp patch beneath it. If it is, don’t touch, block or cut it. Just note it for the engineer.
  6. Top up only as your manual describes. If the pressure falls below about 1 bar with the system cold, follow our guide to topping up low boiler pressure and close the filling controls fully afterwards. Overfilling can make things worse, so see our guide to boiler pressure that’s too high if you overshoot.
  7. Reset once, if needed. If the boiler has locked out on low pressure, use the reset button once if your manual allows it. Our guide to boiler fault codes explains what to note down.

What not to do

  • Don’t keep topping up week after week and hope it settles. Repeatedly adding fresh water can hide a leak that is quietly causing damage.
  • Don’t remove the boiler casing or any panel, or touch gas valves, burners, the pressure relief valve, the expansion vessel or the flue. Under the Gas Safety (Installation and Use) Regulations 1998, only a Gas Safe registered engineer may work on gas appliances.
  • Don’t add leak sealer or other chemicals to the system yourself. Some products aren’t suitable for every boiler, so leave that decision to an engineer.
  • Don’t lift floorboards or open up walls to hunt for a leak, and don’t tighten valves with excessive force.

When to stop and call us

  • You’re topping up more than once or twice a year, or the pressure drops again within days or weeks.
  • The pressure falls to zero, or won’t rise when you use the filling controls.
  • You can see water leaking from a radiator, valve, pipe or the boiler, or there’s a damp patch on a ceiling or wall. Our guides to a leaking radiator and water coming through a ceiling cover what to do in the meantime.
  • The pipe on the outside wall keeps dripping.
  • Your boiler has an external filling loop and the hose has been removed, or you can’t confidently identify the filling controls.
  • The boiler locks out again after one reset.

Our Gas Safe registered engineers carry out boiler repairs across Clare, Sudbury and the surrounding area, and an annual boiler service is a good time to have the system pressure and expansion vessel checked. Bring your pressure log along and it’ll help us get to the bottom of it.

Safety first

Smell gas or suspect carbon monoxide? Leave the property, open doors and windows if it’s safe, don’t use light switches or naked flames, turn the gas off at the meter only if it’s safe to do so, and call the National Gas Emergency Service on 0800 111 999. Get medical advice if anyone has CO symptoms such as headaches, dizziness, nausea or tiredness. You can check that an engineer is registered on the Gas Safe Register.

Never touch electrics near water. If a breaker trips, you may reset it once from a dry spot; if it trips again, leave it off and call a registered (Part P) electrician. If water is leaking heavily, turn off the inside stopcock first (here’s how to find your stopcock). The outside or boundary stop tap is usually owned by your water company (Anglian Water or Essex & Suffolk Water) and may need a special key, so don’t dig it up or force it. Contact your water company about a leak on their side, and check whether neighbours are affected.

Sources and further reading

Boiler pressure keeps dropping? Call Anglian PHE.

Call 01787 278511 or call/WhatsApp 07825 348536 (message us on WhatsApp). With over 10 local engineers, we’ll attend as soon as possible, even at midnight. No call-out fee.

Anglian PHE Ltd, Top Floor, 4 Market Hill, Clare, Sudbury CO10 8NN. Gas Safe 572792, NAPIT registered, trading since 1993.

This is general safety guidance. If you’re unsure, stop and call a qualified engineer.

Similar Posts