Airlock in Water Pipes? How to Clear Spluttering Taps Safely

Taps coughing, spluttering or barely running after the water has been off? Whether a plumber has just worked on your pipes or the water company has repaired a main in your street, the usual cause is air trapped in the pipework. Thames Water notes that water often splutters when it first comes back on and should clear if you run your taps for a couple of minutes. Here’s how to clear trapped air safely, and when an airlock needs a plumber. Everything below uses your taps and the inside stopcock only. Please don’t touch the boiler, the pump or any gas parts.

Is it air, or something else?

  • Spluttering, banging bursts or cloudy water right after the supply returns is almost always air. United Utilities suggests filling a clear glass from the kitchen tap and leaving it to stand: if the cloudiness clears from the bottom up, it’s just tiny air bubbles and nothing to worry about.
  • Weak flow everywhere, with no spluttering is more likely a pressure problem. Our guide to low water pressure covers those checks.
  • No water at all needs a different set of checks, starting with your neighbours. See no water in my house.
  • Brown, blue, green or pink water isn’t air. Don’t drink it, and contact your water company.

How to clear air from your pipes

  1. Start with the cold kitchen tap. This is normally the tap fed directly from the mains. Open it slowly, not all at once, and let it run until the flow is smooth and steady. A few minutes is usually enough.
  2. Work around the house. Open each of the other taps slowly in turn, cold first and then hot, starting nearest the stopcock and finishing at the furthest one, often upstairs. Let each run until it stops spluttering, then turn it off.
  3. Flush each toilet once so the cisterns refill and clear any air in their feed.
  4. Check the inside stopcock is fully open. After plumbing work it’s easy for it to be left partly closed. Turn it anticlockwise until it stops, then back a quarter turn so it doesn’t seize. Our guide shows you how to find your stopcock.
  5. Still weak at the kitchen tap? Water companies such as Yorkshire Water and Severn Trent suggest leaving the cold kitchen tap fully on and turning the inside stopcock off and on a few times. The water may cough a bit, but this often frees trapped air. Only do this if the stopcock turns easily by hand. If it’s stiff, stop. Don’t force it or use tools; see seized or leaking stopcock.
  6. Check your heating and hot water. If you have a combi or sealed system, glance at the boiler pressure gauge once things settle. If it’s low, top it up only as your user manual describes; our guide to low boiler pressure explains how.
  7. Look for leaks. After work on your pipes, check under sinks, around new fittings and below the work area for drips or damp patches.

What not to do

  • Don’t connect a hose between a mains tap and a hot tap to “blast” an airlock out. It can push water the wrong way between supplies and risks contaminating your drinking water, which the Water Supply (Water Fittings) Regulations 1999 are there to prevent.
  • Don’t force a stiff stopcock or valve, and don’t dig up or open the outside stop tap.
  • Don’t take the boiler casing off or touch the pump, gas valves or flue. Under the Gas Safety (Installation and Use) Regulations 1998, only a Gas Safe registered engineer may work on gas appliances.
  • Don’t keep running an electric shower or immersion heater that’s spluttering or running dry. Turn it off and get it checked.

When to stop and call us

  • Spluttering or poor flow carries on after you’ve run every tap and checked the stopcock.
  • Only one tap or the hot water side is affected. That often points to an airlock in a specific pipe, a part-closed isolating valve or a fault from recent work, and a plumber should trace it.
  • Your neighbours’ water is back to normal but yours isn’t. Thames Water says this can be an airlock, and it’s worth checking whether the problem is on your side or the water company’s.
  • The boiler shows a fault code or locks out. You can press the reset button once if your manual allows it, but if it locks out again, call a Gas Safe engineer. Our boiler fault codes guide explains what to note down.
  • You spot a leak, damp patch or water near electrics after the work.

Our engineers handle plumbing repairs and emergency plumbing across Clare, Sudbury and the surrounding area, including tracing stubborn airlocks.

Safety first

Smell gas or suspect carbon monoxide? Leave the property, open doors and windows if it’s safe, don’t use light switches or naked flames, turn the gas off at the meter only if it’s safe to do so, and call the National Gas Emergency Service on 0800 111 999. Get medical advice if anyone has CO symptoms such as headaches, dizziness, nausea or tiredness. You can check that an engineer is registered on the Gas Safe Register.

Never touch electrics near water. If a breaker trips, you may reset it once from a dry spot; if it trips again, leave it off and call a registered (Part P) electrician. If water is leaking, turn off the inside stopcock first. The outside or boundary stop tap is usually owned by your water company (Anglian Water or Essex & Suffolk Water) and may need a special key, so don’t dig it up or force it. Contact your water company about a leak or supply problem on their side, and check whether neighbours are affected too. Our guide to the outside stop tap explains more.

Sources and further reading

Taps still spluttering? Call Anglian PHE.

Call 01787 278511 or WhatsApp 07825 348536. With over 10 local engineers, we’ll attend as soon as possible, even at midnight. No call-out fee.

Anglian PHE Ltd, Top Floor, 4 Market Hill, Clare, Sudbury CO10 8NN. Gas Safe 572792, NAPIT registered, trading since 1993.

This is general safety guidance. If you’re unsure, stop and call a qualified engineer.

Similar Posts